Category: 2021

Wind A Go Go

Kai Iwi Lakes New Zealand

With the world of sailing and global cruising being squeezed by the chokehold of worldwide border closures and restrictions imposed by many countries, we feel very fortunate to be sequestered within the borders of New Zealand.  Although, waiting out the time and tides here has been an awesome experience we’re ready to get Dazzler back on the water to do what she was made to do…sail!  Don’t get me wrong, the New Zealand backdrop for land adventures and scenic vistas has been wonderful but it would seem that we have spent much more time attached to floating concrete real estate fighting off the chill of the prevailing temperatures and sand flies over the last year than sailing.  That being said, we are fortunate to have first world marine tradesmen and parts and accessories available to upgrade our floating, voyaging home in preparation of that day when the gates open and we set sail again for foreign isles.  

We’ve been sailing with sails that were added new in 2009. Our mainsail being the most used sail also is the one that gets the most exposure to ultraviolet light from the sun, has seen better days and has been crying out for retirement. Last August, we started the process of getting quotes for a new mainsail. Quantum USA, Doyle Sails NZ, Willis Sails Opua and Calibre Sails Whangarei. We ultimately chose Calibre Sails here in Whangarei. Quantum was asked for a quote because that is the sail maker I chose back in 2009. Their cruising sails are made out of the country as are the Doyle sails. Willis Sails appear to be made locally but there were some questions with regards to the Dutchman flaking system we have come to rely on while sailing. What pushed Calibre Sails over the top and gained our business was several things. First and foremost the owner David Parr came to our boat to provide us a quote package. He orders the fabric not a cookie cutter sail blank from Bangladesh, China or South Africa. The fabric he chooses in making cruising sails is Fibercon Pro 8.46/9.46 by Contender Sailcloth.

David, also know as Waldo, has a fabric plotting table in his loft that marks all the fabric for the multiple panels of the sail.  The panels are then hand cut and the edges of the fabric are sealed with a hot knife.  The panels are then laid out on the loft floor where the sail begins to take shape.  Seam stick is used for all the 32 mm seams.  The reef diamonds, batten pockets, Dutchman cookies and stress patches are all measured and laid out in preparation for sewing.  

And we got to watch the sail being made…

The coolest part of this whole process is that Waldo allowed us to visit the loft regularly to photograph Dazzler’s sail progress.  We were thrilled to be allowed this privilege.  There’s nothing like seeing your main engine being built from the ground up.

During the process we had to have a new Union Polaris sail logo created. Waldo provided us with about a meter of sticky back sailcloth that we used for the logo. We cut out the old logo from Dazzler’s old sail and took it along with the sticky back cloth to HotPrintz a local printer. We had the large sail logos made along with some smaller logos. One of the smaller logos was attached to Jilly’s new grab bag/purse I made for her from some of the old sail material.

Once Waldo and His crew started work on our sail it went very fast. After we returned to town from visiting friends in the Auckland area for Thanksgiving American style, I visited the Calibre loft to find Nick putting the finishing touches on our nearly completed new mainsail. I was amazed at how quickly they kicked out all the sewing. It was literally less than a week earlier that our sail laid in panels on the floor and now it was basically finished. Incredible!

The day of reckoning has arrived…

A few days later at 0830 hours local time Waldo and Nick arrived on the dock delivering Dazzler’s new mainsail. For the last two months I had spent several hours refurbishing the boom and mast hardware in preparation for the new sail. Everything is in great working order and ready. The new sail went up, up, up, without any glitches. A few adjustments here and there and as Jilly would say, “Bam! Sausage!” There it was gently pulsated against the light morning breeze filling its port side. A thing of beauty. Almost brought a small tear to my eye. I said almost! LOL The sail slid down the Tides Marine Strong Track and flaked atop the boom. With a little adjustment here and there it was perfect. The only thing left is to untie the dock lines and go out and fill the new sail with a fresh breeze. To be continued.…

Of course the resident photographer was busy snapping photos and videos to create hero moments later. LOL We couldn’t be happier with our choice of sailmaker and sail product. Calibre Sails gets our vote for best sailmaker in Whangerie. To Waldo and Nick, you guys rock!

Note…No polyesters were harmed during the construction of this sail or asked to do things outside of their performance descriptions.  LOL  

Let the wind fill your souls and sail as you streak toward the sunset and safe harbor.  Wind  a go go.  Cheers!

Captain Dan

Check back soon for a video showing the entire process….

The 12 Mile Journey

It was the best of times.  It was the worst of times….as the story goes.  We are safely tucked behind the near impenetrable boarders of New Zealand from any outsiders.  Unless you are bringing big dollars to the economy like the America’s Cup Yacht race et al.  We have weathered the various lockdown levels from 4 to 1 and are not the worst for wear.  Last February and early March just before the holy lockdown happened, we were perched above the ground at Harbourside Yacht Works.  Dazzler’s bottom had two shiny new coats of Sea Zone 60 bottom paint.  And we were finishing up with giving Sparkle, our tender, a new paint job as well.  We completed a few other hard stand projects before launching back into the water. 

Purchased at Wynn Fraser Paints

Once in the water and a few days prior to New Zealand’s borders slamming shut into level 4 lockdown we docked at Whangarei Marina where we planned to wait out the world pandemic crisis.  Normally we would have departed the chilly climate of New Zealand in April for the warmer waters in the tropical islands of Fiji.  This year added a higher degree of difficulty to our plans to say the least.  

The beginning of August, I noticed that Dazzler’s bottom paint just below the water line was starting to look a bit shaded with marine slime coating.  It had been just over four months since we dropped her in the water and it was getting time to think about giving her underside a bit of a cleaning.  August is about as the middle of winter as you can get here in New Zealand.  I wasn’t looking forward to jumping into the water for any reason.  So, I started to research the possibility of having Dazzler lifted out of the water and get a light pressure wash done on her underside.  

After several days of yard and lift shopping we settled on the hydraulic trailer lift at Marsden Cove Marina.  We made an appointment for the 19th of August for a haul, wash and splash.  

As you can see, after four months there was very little slime coat on Dazzler’s bottom.

Any plans to leave the Whangarei Marina should be coordinated with Mother Nature and her tides.  Marsden Cove Marina is approximately 11 miles down river near the river’s mouth which  is about two hours one way.  Allowing two to three hours for the haul, wash and splash would mean that we would be at low tide and would have difficulty getting back into our slip.  Thus we decided to stay the night at a dock in Marsden Cove Marina and head up river the next day at or near high tide.

When the 19th arrived we were out of the slip on time, but we didn’t plan to make Hatea River bridge opening and we had to wait until 0830 hours for the bridge operator to open the bridge.  Because we were a little behind schedule we called Marsden Cove Marina to let them know we’d be about 30 minutes late.  

Once we arrived and after tying up to the haul out dock, the yard crew lowered their new looking hydraulic trailer under Dazzler.  The trailer had a gap between its left and right sides with beefy sets of dual tires along each rail.  The hydraulic operator handled the trailer’s equipment like a highly trained surgeon.  The trailer’s hydraulic pads were raised one by one until they gently made contact with Dazzler’s hull.  Before we knew it Dazzler was being leveled on the trailer and pulled out of the water.  I have to say of all the different times she has been pulled out of the water this time caused the least amount of stress.  

The crew pulled Dazzler across the road and into the wash bay where they used a pressure washer to spray off what is know as the slime coating that builds on the surface of the paint.  There were no barnacles or other larger marine organisms attached to her bottom.  The operator had the pressure turned down so low that there was almost no leaching of the paint off of Dazzler’s bottom.  There were four hydraulic pads along each side of her hull.  The hydraulic operator put braces under Dazzler’s keel and lowered one pad at a time to allow the spray operator access to clean under the contact points of her hull.  

After all the spraying had been completed, I removed the old shaft zinc and attached a new one.  Less than an hour later she was ready to be moved back down to the water and launched.  We walked alongside like we were line tenders of a Macy’s balloon walking down 5th Avenue.  Once in the water again and tied to the haul out dock it was all over except for paying the bill.  Off to the office we went.  About $300.00 NZD (@$195.00 USD) later we were done.  We stopped at the cafe for a bite to eat and then back to Dazzler to move her to her dock across the channel for the night.  Some good friends Deb and Phil Perfitt of the vessel Coastal Drifter were boat watching in the marina and treated us to a nice dinner and companionship.  Great way to finish off a productive day.

The next morning early we were untied and heading up river back to Whangarei Marina.  All is  well that ends well. 

Just a side note:  Sea~Zone 60 self polishing ablative bottom paint by Altex.  Wow!  Last season when we arrived in New Zealand we needed to re-paint Dazzler’s bottom.  We settled on Sea~Zone 60 for our new paint.  We also had to apply a primer coat to insure chemical bond to the older sanded hard Trinidad paint.  During the cruising season of 2019, we cruised the waters of Tonga and Fiji for almost six months.  During which we had to give Dazzler’s bottom a wipe down twice to remove the slime coat.  The self polishing properties of Sea~Zone 60 paint seemed to work as advertised.  I was impressed as to how clean the bottom stayed during our travels.  

Last January when we hauled Dazzler out prior to our USA trip, we found the condition of the bottom paint to be in very good condition with no visible barnacles.  Impressive!  There were a few thinned areas but over all in good condition.  

Once we returned from the states, we decided to add two additional coats of Sea~Zone 60 to cover up the few thinned areas.  The paint is easy to apply, easy to maintain and appears to hold up well against various marine organisms just as advertised.  

I would like to see the paint durability a bit more substantial to maybe get two years of use before re-coating.  But it’s ability to fend off marine organisms is very good.  The only down side to Sea~Zone 60 appears to be its retail price.  We will probably add two more coats next March in preparation of departure back into the sailing lifestyle. 

Cheers!

Captain Dan

P.S.  We both were very impressed with the ease, operation and the skill of the Marsden Cove Haul out crew.  Sending a special thanks out to Mark, Remi and Adam for a job well done! We highly recommend their services. It would be well worth your time and money in our humble opinion.

Here’s a short video of the haul out. Enjoy!